EN
EN
22
23
2. Clean the water tank, filter holder, espresso filters, milk jug, tamper, and hop-
per lid (see: ‘Care and Cleaning’). Ensure that the hopper lid is completely dry
before closing the bean hopper with the hopper lid.
3. After cleaning, place the appliance on an appropriate working place near a
suitable wall power outlet (see: ‘Important Safeguards’).
IMPORTANT -
When removing or replacing the water tank or filling the water
tank, while it is mounted at the appliance, always keep the bean hopper closed.
This will avoid that spashes get into the bean hopper. The tank lid cannot be remo-
ved. For opening the water tank, pull the tank lid up to the stop and fold the tank
lid back to the rear of the machine.
4. Fill the water tank at least up to half height. For this, you may remove the water
tank. Alternatively, use an appropriate caraffe for filling the water (see: ‘Opera-
tion’). Carefully avoid to spill the water onto the machine.
5. Insert the power plug into the wall power outlet and press the on/off button to
switch on the appliance.
PREPARATIONS AFTER PURCHASING
NOTE
These preparations have to be done once after purchasing the machine, or after a
reset to factory settings (see: ‘Entering Your Own Settings / Reset to Factory Settings‘).
On almost each page of the initial start procedure, a framed area (button) is shown
labelled with “Done” or “Next”. Touch this button to switch to the next page. When
you made a typing error, simply touch the arrow in the navigation bar (leftmost
column on the screen) for getting back to the previous page (see: “Design of the
Screen-Based Control / Navigation Bar’). The navigation bar appears on almost
all pages of the initial start procedure. All your settings may be changed later on.
Selecting the Language
For selecting the language used for the texts on the screen, the flags of the appro-
priate nations are shown on the screen.
6. Touch the flag of the nation, which native language you wish to select. On the
next page, this flag is centred on the screen.
7. Touch “Done” for confirming your selection and entering the next step.
Measuring and Entering the Water Hardness
The water hardness detemines the intervals for descaling that have to be met for
avoiding damage to the water system caused by scale deposits. During the initial
start procedure, instructions concerning the measurement of the water hardness via
the provided test strip are shown.
NOTE
Your local water supplier (water works or bottling plant) can give information on
the hardness of the water. Nevertheless, please consider that the water hardness
of your tap water may be much higher than stated by your water works, because
the water hardness is impaired by the state of the water pipes in your house. If in
doubt, you should use a test strip.
IMPORTANT -
There are various types of test stripes on market that differ from each
other in handling and display. The screen pages of the appliance are adapted to
the type delivered with the appliance.
When using any other type, refer to the
instructions on the pack
for performing the measurement. Thereafter, enter your
result via the screen page showing the coloured graduation and select the appro-
priate value. The unit shown via the appliance is ppm.
Refer to the following table for converting the usual units of water hardness to the dis-
played value of the appliance. For this, in the column named with the unit used for
your test result select the line showing the appropriate range of valures. In this line read
the assigned value in ppm (display), whitch is shown on the display of the appliance.
Water Hardness
ppm (display)
°dH
°e
°f
soft
0
0
0-1
0-1
25
1
1.5-3
2-4
medium to
hard
50
2-5
3-8
5-10
120
6-13
8-17
11-22
hard to
very hard
250
14-23
17.5-30
23-40
425
above 24
above 30
above 40
IMPORTANT -
While unpacking and using the test strip, avoid touching the indi-
cator area (bulge at one end of the test strip) with your fingers, because this could
infuence the testing result.
8. When using the provided test strip, proceed according to the instructions on the
screen. When using another type of test strip, refer to the instructions on the pack
and switch directly to the coloured graduation. Touch the area with the closest
match to your result.
