EN
EN
24
25
NOTE
If you wish to use another water quality later on, you should check and enter the
water hardness again. Select the command “Guide and Setting / Mainenance /
Water hardness” for showing the required pages.
Installing the Water Filter
CAUTION
– Especially, when using hard water, we strongly recommend to
use the dedicated water filter, because scale deposits within the water system may
damage the machine. However, only use water filters that are recommended by
the manufacturer. Other types of filters may damage the machine. If requrired, get
in contact with your vendor.
IMPORTANT -
For rinsing and soaking the water filter, use clear, cold tap water. If
the appliance is used normally (daily), the water filter has a lifetime of two months,
If the appliance is used only rarely and the water filter is installed, the water filter
has a lifetime of max. 3 weeks.
NOTE
We recommend to prepare and install the water filter on a sink or over a large,
flat bowl. You need a high vessel, where you can immerse the water filter com-
pletely in an upright position.
1. Pull the water tank vertically upwards and out of the appliance. If required, pull
out the old water filter. Rinse the water tank and fill it with approx. 2 litres of
cold, clear drinking water (at least 3/4 of its height).
2. Remove the water filter from the packaging. Turn the date disk to the month after next.
3.
Preparing the water filter for use:
Fill a sufficiently high vessel with cold tap
water. Let water run into the holes of the filter until the water comes out of the other
openings. When shaking the water filter, you may hear no rustling of the filter mate-
rial. Then, completely immerse the water filter in your prepared vessel, while tilting
the filter in all directions and slightly squeezing it for removing any air bubbles.
NOTE
The filter is filled correctly with water, when it is not swimming.
If there are air bubbles
in the water filter, it will not stay on its seat in der water tank but come up to the surface.
4.
Installing the water filter:
While holding the water filter with the holes facing
upwards, take it out of your vessel and immerse it completely into the water tank.
With the water filter still immersed, turn it upside down and place the filter onto
the short tube over the valve at the bottom of the water tank. Push the water filter
down until it is kept in place.
5. Fill the water tank up to the MAX filling level with fresh, cold drinking water and
wipe dry the exterior. Then let the water tank slide vertically down at the rear of
the appliance. If required, push it down gently. Close the tank lid.
6. Touch the button “Next”.
FLUSHING THE WATER SYSTEM
WARNING
– During flushing, hot water comes out of the group head and
steam wand. Do not hold your hands and arms under the group head or steam
wand. Expect splashes in the front area of the machine. Please consider that the
water in the drip tray may be hot.
CAUTION
– Do not operate the appliance, when the drip tray is missing
or not installed correctly. Do not let any liquids run under the appliance.
1.
Preparing the machine:
If required, empty the drip tray and ensure that the drip
tray is in place correctly. Fill the water tank to the “MAX” marking with fresh,
cold drinking water (see: ‘Operation / Preparing the Maschine for Operation’).
2. Follow the instructions on the screen. For this, turn the steam wand to the rear of
the machine. Then, by holding the black handle of the filter holder in the 8 'o
clock position, you can insert the filter holder from below into the group head.
Turn the filter holder to the right side of the machine until the handle points in
right angle to the front of the machine. Doing so, you will notice a rremarkable
resistance. Point the steam wand to the large hole in the metal grid of the drip
tray. This will minimize splashing.
NOTE
Lock icons (open and closed) at the group head indicate the correct positions for
the handle of the filter holder, while installing and locking the filter holder at the
group head. Group head and steam wand are purged via 2 flushing cycles each.
On the screen, several pages inform you on the procedure.
3.
Flushing:
Touch the buttons “Next” and “Start” for starting the procedure and let
the machine run though the 4 flushing cycles. Thereafter, a message is shown:
“Your machine is ready to use!”
NOTE
After the preparations are done, the on/off button gets dark shortly. Then, the
machine switches on automatically. A message is shown: “Turning the maschine
on”. Wait until the home page is displayed (see: ‘Design of the Screen-Based
Control’).
