EN
EN
44
45
WARNING
– Always stop the steam function, before removing or inserting
the steam wand. Otherwise, hot milk may splash violently.
When the froth
amount is adjusted to “Maximum”, the steam function is operated with maxi-
mum pressure. In this case, especially be aware that milk could splash or over-
flow, even when the texturing procedure is performed correctly.
Keep a suffici-
ent distance to the machine and hold the milk jug by the handle.
NOTE
You may turn the steam wand to an appropriate position for getting good access.
For this, only touch the dark handle of the steam wand, because
the metal parts
will be very hot
. While steam is generated, a pumping noise can be heard.
7. Hold the milk jug under the steam wand and immerse the nozzle (thickening at
the end of the steam wand) at least up to half its heigh into the milk. You should
hold the steam wand near the side wall of the milk jug and insert it at an angle.
Then touch the jug icon again for starting the procedure. The steam generates a
vortex in the milk.
8. When the volume of the milk increases and you wish to get a really rich texture,
carefully lower the milk jug a little for bringing the steam wand a little more to the
surface of the milk. This will blow some more air into the milk. However, when
many large bubbles are made, you should immerse the steam wand somewhat
deeper. If you wish to get hot milk and only a little froth, keep the steam wand
immersed deep in the milk.
9. As soon as the milk is textured and heated sufficiently, touch the “Stop” button for
stopping the steam function. Wait until the steam flow is stopped. Than, carefully
remove the milk jug from the steam wand.
WARNING
–
The steam wand is very hot after use!
Carefully ensure not
to touch the metal parts with your skin or heat-sensitive objects.
IMPORTANT -
Wipe the steam wand after each use to avoid that proteins and
carbohydrates of the milk clog the steam wand nozzle and/or cause a stale odour
and taste of the milk.
10. Wipe the steam wand via a moist, clean cloth (e.g. kitchen towel) for removing
the residues of milk. Doing so,
carefully avoid to touch the steam wand with
your skin
. After wiping, direct the steam wand to the drip tray.
11.
Keep your hands away from the steam wand
, while touching the jug icon
again. Let a blast of steam blow out any residues of milk. After approx. 2-3
seconds, touch the “Stop” button for stopping the steam.
12. Pour the hot milk below the froth in your drink and spoon the milk froth on it.
Consume textured milk immediately, because milk froth collapses after a short
time.
13. At the latest at the end of the day, you should thoroughly clean the steam wand
(see: ‘Care and Cleaning’).
MAKING TEA OR OTHER HOT DRINKS
The appliance provides hot water with various temperatures for tea and other hot
beverages. The temperatures are adapted to the tea types given on the tea page.
The tea types are sorted in ascending temperatures from left to right.
NOTE
The tea function may be used for pre-warming the filter holder and cups as well as
for preparing any other hot drinks that require just hot water (e.g. cocoa mixtures,
instant coffee). If you wish to prepare another type of drink, simply select the tea
type, which is brewed with the desired temperature.
1.
Selecting the tea type:
For displaying the drink type page with 4 different tea
types, on the home page select the drink type “Tea” by touching the appropriate
cup icon. For each tea type a different temperature is programmed. Touch the
desired tea type. The following drink page shows the control area with the cup
icon on the screen.
2.
Pre-heating your cup:
Direct the steam wand into your cup. Then touch the cup
icon on the screen. Maybe, a message is shown first, while the water system is
heating. Then, the programmed amount of hot water is given off. Let the appli-
ance operate, until the function is complete and the drink page is shown again.
Toss the hot water for some seconds in your cup. Then discard the water.
NOTE
You can stop the hot water function any time you like. Simply touch the “Stop”
button.
3.
Preparing your cup:
Fill in the ingredients for your drink. For example: place a
tea bag into the cup or fill in instant powder.
4.
Selecting the volume:
If required, touch the gear icon (“Size”) for displaying the
setting page (see: ‘Design of the Screen-Based Control / The Setting Pages’).
Select the desired value and touch the arrow in the navigation bar for returning
to the drink page.
