Gaspardo DP Скачать руководство пользователя страница 31

Страница: 31 / 62

USE AND MAINTENANCE

ENGLISH

cod. 19501170

5.0.6 EMPTYING THE HOPPER

To empty the hopper of all remaining seeds, proceed as follows:
Place a bag or container under the discharging door of the
distributor, then open it by unscrewing the wing nut. By doing so,
any small remainder of seeds can easily and completely be removed
from the hopper. It is recommended to turn the small paddle wheel
of the distributor, to remove any final residue.
Once this operation has been completed, shut the discharging door
again by fastening the wing nut.

5.0.7 SETTING ASIDE

At the end of the season, or if a long period of rest is for seen it is
advisable:

1) Carefully empty all the seed from the hopper and distribution

ass’y.

2) Wash the equipment with a lot of water, especially the tanks,

and than dry them.

3) Carefully check worn or damaged parts and replace if necessary.
4) Tighten all screws and bolts.
5) Grease the dnve chains, oil all the drive chains, spread lubricant

on all the parts not painted.

6) Protect the equipment with a (nylon) cover.
7) Then put it in a dry place, do not move it and where it is out of

reach of un authorized people.

If these operations are done carefully, it will be to the total advantage
of the user because when work is recommenced, he will find the
equipment in perfect conditions.

5.1 SUGGESTIONS IN CASE OF INCONVENIENCES

5.1.1 CLOGGING OF THE PIPES

Check, on the basis of the rotation test chart, the position of
the butterfly valves.

The blades are clogged with wet soil

The distribution pipes are bent somewhere.

Foreign bodies in the distributor or blade.

Respect the rpm, 540 or 1000, of the power take-off.

5.1.2 THE AMOUNT OF SEED IN KG/HA DOES NOT
CORRESPOND TO THE VALUES OF THE ROTATION TEST

The causes involved in the excessive amount of seeds dispersed
may be:
-

during the rotation test the drive transmission wheel was turned
too fast.

The causes involved in an insufficient amount of seed dispersed
may be:
-

dosing unit access clogged by foreign bodies.

during the rotation test the empty weight of the collecting
container was not taken into account and deducted.

The differences due to slipping or excessive distribution at the
beginning of the field, are around 2-4%. Greater deviations can
be traced back exclusively to errors in the rotation test, to a wrong
transmission ratio or similar causes.

5.2 SUPPLY

Current supplied equipment

Hydraulic folding chassis (only for DPI);

Seed covering harrow;

Lights.

Optional equipment:

Row marker hydraulic control;

Electronic hectare counter;

Electronic row exclusion;

Hopper extension (for DP250/300/400 - DPI400);

Conversion from cast iron wheel to farmflex wheel;

Conversion from cast farmflex wheel to iron wheel;

Cast iron seed press wheel narrow;

Oil pipe reduction from 6 to 2 with solenoid valve (folding fra-
me and transport wheels;

Centralised greasing;

Oil assisted braking system;

Seed level electronic control;

Screw-feeder;

DP250 and DP300 conversion from driving to drawing;

DP250 and DP300 conversion from pulling to drawing;

Distribution transmission (1:2).

Equipment may vary according to country of destination.

Finally, we remind you that the manufacturer is always
available for any and all necessary assistance and spares.

6.0 SPARE PARTS

Orders must be transmitted through our area dealers and should
always include the following indications:

Type, model and serial number of the machine

. These

data are punched on the data plate with which every implement
is equipped

Code number of the required spare part

. This will be found

in the spare parts catalogue.

- Description of the part and required quantity.

- Table number.

Means of dispatch

. If this item is not indicated, the

Manufacturer, while dedicating particular care to this service,
shall not be held responsible for delays in delivery caused by
cases of force majeure.
Transport expenses shall always be at the consigneeÕs charge.
The goods travel at the purchaserÕs risk and peril even when
sold ex destination.

NOTE:

The symbols

(Dx) right

and

(Sx) left

, concerning the

machine or single parts of it, are referred, as in the figure, to a rear
view of them. Exceptions will be indicated.