GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 75

Страница: 75 / 78

TR-HT2xx LED Controller - User Manual

Error number

Reason

Err 8, 12

EEPROM corrupt. The configuration has been
cleared.

Err 9, 20

Settings could not be saved to EEPROM.

Err 13

command: The resync event cannot be found.

The channel or tag values may be wrong or the delay
period may be complete.

Err 19

A light has been connected, but no rating has been
set.

Err 21, 23

A sensing error has occurred. See Section 7.6, Fault
detection.

Err 22

The light is not compatible with the controller. The
TR-HT does not drive the light and the web page
reports

Triniti Chip device protection

Err 27

Ethernet settings cannot be read from EEPROM.
They may be incorrect.

Err 34, 37

The internal power dissipation is too high. Output is
turned off.

Err 35

The output current to the light is too low.

Err 36

The output is short circuit.

Err 37

The voltage required for the lighting has increased
too much. Check for ageing of the light or a failed
LED.

Err 38

The voltage required for the lighting has decreased
too much. Check for ageing of the light or a failed
LED.

Err 39

The internal protection has prevented the
SafePower voltage going too high.

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды