GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 29

Страница: 29 / 78

TR-HT2xx LED Controller - User Manual

7.6

Fault detection

The TR-HT can detect a range of errors when connected to a light. The
displayed errors are shown below with their reasons.

Error
display

Reason

Internal power dissipation is too high. Output turned off.

Output current to lighting is too low. The light is open
circuit or there is not enough supply voltage for the
requested output current.

Output voltage is too low. The TR-HL detects that the
output is short-circuited.

The voltage required for the lighting has increased too
much. Check for ageing of the light or a failed LED.

The voltage required for the lighting has decreased too
much. Check for ageing of the light or a failed LED.

Note:

When the output current falls below 100mA, some fault detection is

disabled. Press

SEL

to cancel the error and allow the TR-HT to sense the

light again.

7.7

Factory settings

You can clear the TR-HT configuration to return it to its factory settings:
The lighting rating is cleared and the light does not illuminate.

Clear the configuration from the front panel by pressing and holding

SEL

for about 5 seconds, until

Select Opt

and

Chan 1

is displayed. You can

also clear the configuration by using the

command (see

Section 12.3.3,

General commands

You can start the TR-HT from a powered down state (cold boot) with the
front panel keypad locked; this process removes the keypad lock.

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды