GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 55

Страница: 55 / 78

TR-HT2xx LED Controller - User Manual

Note:

If you set the brightness to more than 100%, the pulse width is

limited to a safe value as described in

Section 7.1, Pulse and duty cycle

limits

12.2.7 Setting time periods

When the TR-HT requires you to enter a numeric value, the second line of
the display flashes indicating that you can use the

and

keys to

change the range, or press the

SEL

button to enter a value using the

and

buttons.

To set pulse delay, retrigger and pulse width values, select the required
range from the table below (delay is shown as an example):

Display

Range of values

Values are displayed in seconds from 10ms
to 5 seconds in steps of 10ms.

Values are displayed in milliseconds from
1ms to 999ms in steps of 1ms.

Values are displayed in milliseconds from
0.1ms to 99.9ms in steps of 0.1ms.

Values are displayed in milliseconds from
0.01 ms to 9.99 ms in steps of 0.01ms.

Values are displayed in microseconds from
1μs to 999μs in steps of 1μs.

To enter the value, press the

SEL

button to select the range, and use the

and

buttons to set a value. Press the

SEL

button to complete setting

the value.

Refer to

Section 13, TR-HT reference information

for the permitted range

of values that can be used when setting up your TR-HT controller.

12.2.8 Setting the internal trigger timer

You can set an internal trigger timer when the TR-HT is in pulse mode.
When set, the TR-HT triggers with the same delay and pulse width already
set up as described in

Section 12.2.6, Setting up pulsed operation

External triggering remains enabled.

Ensure the TR-HT is set to pulsed operation. To set the period of the
internal trigger timer, press and hold

SEL

for 1 second,

Select Opt

and

Chan 1

are displayed. Follow the keystrokes overleaf:

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды