GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 53

Страница: 53 / 78

TR-HT2xx LED Controller - User Manual

Trig 1

is displayed. Use the

and

buttons

to select

Trig 2

if you want to use trigger input

2. Press the

SEL

button.

The trigger is set to

Positive

, or active high.

Press the

SEL

button to keep the trigger

positive.

Or...

If you wish to set the trigger negative, or
active low, use the

and

buttons to select

Negative

. Press the

SEL

button.

Error detection is disabled. Press the

SEL

button to keep it disabled.

Or...

If you wish to enable error detection, use the

and

buttons to set the

Err flag

Enabled

. Press the

SEL

button.

Selected output is set up.

12.2.6 Setting up pulsed operation

Set up pulsed operation if you want your light to come on for a
predetermined period on a trigger pulse. Press and hold

SEL

for 1

second,

Select Opt

and

Chan 1

are displayed. Use the

buttons to

select the channel you want to set up, and follow the keystrokes below:

CH1

is displayed. Use the

button to

select the required channel.

Press the

SEL

button.

Use the

and

buttons to select

Pulse

and press the

SEL

button.

Brightness

is displayed and a value of 0.0%

highlighted. Use the

and

buttons to

select the required brightness from 0.0% to
999.9%. Press the

SEL

button.

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды