GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 57

Страница: 57 / 78

TR-HT2xx LED Controller - User Manual

Note:

Setting a lock code does not prevent a cold boot of the TR-HT. A

cold boot clears the lock code.

To unlock the keypad, press and hold

SEL

for 1 second and follow the

keystrokes below:

Keypad Locked

is displayed. Keep pressing

the

SEL

button.

Unlock

is displayed. Press the

SEL

button.

Use the

and

buttons to enter the lock

code, and press the

SEL

button.

The TR-HT keypad is unlocked.

If the code entered is incorrect,

Keypad

Locked

is displayed.

12.2.10 Viewing the trigger status

You can view the trigger input status and whether the light is pulsing when
the TR-HT is set to pulse or switched mode. To do this, press and hold

SEL

for 1 second,

Select Opt

and

Chan 1

are displayed. Follow the

keystrokes below:

Use the

and

buttons to select

Trig Chk

and press the

SEL

button.

The trigger inputs are displayed. The active
trigger is highlighted.

Press the

SEL

button.

The TR-HT returns to normal operation.

12.2.11 Viewing the output current

You can view an approximate measure of the output current from the
TR-HT front panel. The current measurement is updated roughly once per
second, but this can be slower when the TR-HT is set to pulsed operation.

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды