GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 78

background image

TR-HT2xx LED Controller - User Manual

5

Mounting the TR-HT

Mount the TR-HT on a flat surface using M4 screws through the mounting
holes in the unit's case. The illustration below shows the positions of the
mounting holes.

5.1

Environmental considerations

The TR-HT enclosure is a fire enclosure as long as it is mounted so that
none of the connectors are facing downwards.

If a fire enclosure is used, the enclosure should be metal or plastic (with a
flammability rating of UL94 V1 or better) and with no holes below or to the
sides of the TR-HT when mounted. Cable entries below the TR-HT should
be through glands that also have a flammability rating of UL94 V1 or
better. The TR-HT should be at least 10mm from any other part or side of
the enclosure. The TR-HT does not have an IP rating and must be
mounted so that moisture and dirt cannot enter the unit.

—

16

—

«
...
14
15
16
17
18
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: Zolix Instruments Страницы: 22

Бренд: Datalogic Страницы: 15

Бренд: Lamtec Страницы: 136

Бренд: Valcom Страницы: 6

Бренд: Watlow Страницы: 4

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: Daruifuno Страницы: 24

767-4803/000-800

Бренд: WAGO Страницы: 80

Vertical Fan Coil

Бренд: Solaris Страницы: 10

Бренд: S&C Страницы: 24

Бренд: Sven Страницы: 6

Бренд: Blucave Страницы: 2

Smart 4 Universal

Бренд: Classic Страницы: 12

Бренд: Pilz Страницы: 9

Бренд: Danfoss Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды