GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 78

background image

TR-HT2xx LED Controller - User Manual

3

Sicherheit

Bitte lesen Sie vor Verwendung des TR-HT diese Informationen. Beachten
Sie immer die folgenden Sicherheitshinweise. Wenden Sie sich im
Zweifelsfall an Ihren Händler oder Gardasoft Vision. Die folgenden
Symbole haben die folgende Bedeutung:

Warnung:

Lesen Sie die Hinweise, um eine mögliche Gefahr zu

verstehen.

Warnung:

Oberfläche kann heiß werden.

Warnung:

Mögliche gefährliche Spannung.

Wenn diese Symbole in der Anleitung auftauchen, enthält der Text
Hinweise zu den zu ergreifenden Vorsichtsmaßnahmen.

3.1

Wärme

Stellen Sie sicher, dass der TR-HT korrekt montiert ist (siehe

Mounting the TR-HT

) und dass Sie die Grenzwerte für das Gerät nicht

überschreiten (siehe

Section 13, TR-HT reference information

).

Bei den maximalen Grenzwerten kann das Gehäuse des TR-HT 65°C
überschreiten, was ausreichend ist um bei einer Berührung zu
Verbrennungen zu führen. Positionieren Sie das Gerät so, dass eine
versehentliche Berührung durch das Personal ausgeschlossen ist und
stellen Sie sicher, dass Luft frei um das Gerät zirkulieren kann.

3.2

Elektrik

Die TR-HT produziert energiereiche Pulse. Achten Sie darauf, die
Ausgänge korrekt anzuschließen und die Ausgangsverdrahtung und die
Verbraucher vor Kurzschlüssen zu schützen. Nach dem Ausschalten wird
die Energie noch etwa 2 Minuten lang in der TR-HT gespeichert.

Das TR-HT erzeugt Impulse mit hoher Energie. Achten Sie darauf, die
Ausgänge korrekt anzuschließen und schützen Sie die
Ausgangsverkabelung und Last gegen Kurzschlüsse. Beim Ausschalten
bleibt Energie für etwa 2 Minuten im TR-HT gespeichert.

Das TR-HT verfügt über keine vollständige Nachlaufisolierung der
Eingänge (einschließlich Trigger- und Kommunikationsports) und
Ausgänge. Beachten Sie daher unbedingt die folgenden Hinweise:

Computergeräte, die an die Kommunikations- oder Trigger-Ports
angeschlossen sind, müssen über eine interne Stromversorgung verfügen
oder vom Stromnetz durch eine doppelte Isolierung/verstärkte Isolierung
getrennt sein oder nach dem Standard IEC 60950-1 zugelassen sein. Alle

—

10

—

«
...
8
9
10
11
12
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: Faber Страницы: 8

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Patron Страницы: 17

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Saluki Страницы: 13

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: H-Tronic Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды