GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 61

Страница: 61 / 78

TR-HT2xx LED Controller - User Manual

brightness setting in percent (0 to 999)

retrigger delay in milliseconds ( 0.1 to 999). This
parameter is optional and if not set, the
minimum allowed retrigger time is set.

Note:

An error message is returned if the brightness setting requires

a greater current than the maximum current output or if the
combination of pulsed width and brightness is not allowed under the
limitations of the unit.

Set the option flags

This command sets the flags for error detection, trigger sense, and
SafeSense:

REc,m

Where

= the output channel (1 to 2), and

can take the following

values:

Error
detection

Trigger sense

SafeSense

Enabled

Disabled

Enabled

—

Enabled

Disabled

—

Enabled

Disabled

Enabled

—

Disabled

—

Disabled

Set the trigger input

This command sets the input used for pulse and switched output
modes.

RP,c,p

Where:

output channel (1 to 2)

trigger input (1 to 4).

Set the internal trigger

These commands control the internal trigger. When set, the output
is triggered using an internal trigger signal. Type in:

TT0

to disable the internal trigger

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды