GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 66

Страница: 66 / 78

TR-HT2xx LED Controller - User Manual

gate input:

0 for none

1 to 4 for IP1 to IP4

5 to 6 for OP1 to OP2

flags.

For example:

ZS1,3,2,0,2

Sets output channel 1 to pulse mode (Ptt), triggered by input 2, no
gate input, and flags = 2 (to invert the output).

Note:

The flags

parameter must be entered as a decimal number.

Set the output pulse timing

Use this command to set the output pulse delay and pulse width
timings:

ZTc,p,d

Where:

output channel (1 to 2)

pulse width (time or encoder pulses)

delay time (time or encoder pulses)

The pulse width and delay times can either be set as a time period or
as a number of encoder pulses set in the mode parameter of the

command.

For example:

ZT2,3ms,5K

Sets output channel 2 to provide a 3ms pulse after 5000 encoder
pulses.

Note:

Set the output mode with the

command

before

setting

the pulse timing.

Set the retrigger time

The retrigger time is the minimum time from when an output is
triggered to the next time it is triggered. The mode must be set
before the retrigger time.

ZRc,r

Where:

output channel (1 to 4)

retrigger time or number of pulses.

For example:

ZR2,10ms

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды