GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 62

Страница: 62 / 78

TR-HT2xx LED Controller - User Manual

TT1

to enable the internal trigger using the period last set

TT1,p

to enable the internal trigger and set the period.

Where:

= trigger period in milliseconds.

Note :

The

TT1

command does not disable external triggers.

Save the settings to memory

This command saves the settings to non-volatile memory. If you
power cycle the TR-HT before sending the

command, all

changes are lost and the unit returns to the values set before the last

command.

Clear configuration

This command clears the configuration and lighting ratings, and
turns the output off. The results of any

, and

commands are cleared.

Show configuration

This command shows the configuration of the TR-HT. Type in:

A typical reply to this command might be:

CH1,MD0,S50.0,0.0,DL1.000ms,PU1.000ms,

RT 0.0us,IP1,FL0,CS0.000A,RA0.000A

CH2,MD0,S50.0,0.0,DL1.000ms,PU1.000ms,

RT 0.0us,IP1,FL0,CS0.000A,RA0.000A

Where:

channel number

mode: 0 = continuous, 1 = pulsed, 2 = switched

brightness percentage setting:

First setting used in all modes

Second setting only used for selected mode

pulse delay

pulse width

retrigger delay

input trigger (set using the

command)

—

Содержание TR-HT2 Series















































































Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды

GARDASOFT TR-HT2 Series, Руководство пользователя

Результаты поиска

Содержание TR-HT2 Series

Отзывы:

Похожие инструкции для TR-HT2 Series

Бренды по названию

Популярные бренды