GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 78

background image

TR-HT2xx LED Controller - User Manual

anderen Geräte, die an die Trigger- oder andere Ports angeschlossen
sind, müssen ebenfalls durch eine doppelte Isolierung/verstärkte
Isolierung vom Stromnetz getrennt sein.

Das Netzgerät, das zur Stromversorgung des TR-HT dient, muss durch
eine doppelte Isolierung/verstärkte Isolierung von der Stromversorgung
getrennt sein und gegen Kurzschlüsse und Überlastungen geschützt sein.
Wir empfehlen die Verwendung eines Netzgeräts, das den
Ausgangsstrom durch konstruktive Maßnahmen, durch Einstellen der
Stromgrenze an der Versorgung (wenn möglich) oder durch einen
Überstromschutz auf den geeigneten Nennstrom der Steuerung
begrenzt. Das Netzgerät muss nach IEC 60950-1, IEC 60335-1, IEC
61010-1 oder IEC61558-1,-2,-16 zugelassen sein. Das Netzgerät kann
auch nach gleichwertigen oder höheren Standards zugelassen sein.

Alle stromführenden Leiter, die vom Stromnetz abgeleitet sind, müssen
ebenfalls Sicherheitskleinspannung (SELV) am Ausgang erzeugen.
Hinweise zu den zulässigen Spannungsgrenzwerten finden Sie im

13, TR-HT reference information

.

Bei den maximalen Grenzwerten kann die Temperatur des Gehäuses
65°C überschreiten. Daher muss entweder die gesamte Verkabelung für
mindestens 100°C bemessen sein oder die gesamte Verkabelung muss
zusätzlich mit einer angemessen dimensionierten wärmebeständigen
Tülle isoliert sein oder gegen Kontakt mit dem Metallgehäuse der
Steuerung oder deren Kühlkörper, sofern angebracht, geschützt sein.

Die Verkabelung der Stromversorgung zur Steuerung muss für
mindestens 20A bemessen sein.

Die Verkabelung vom Kanalausgang zur Last muss höher als der
maximale Kanalausgangsstrom dimensioniert sein.

Wenn die Steuerung falsch eingerichtet ist oder im Fall eines Fehlers, kann
es vorkommen, dass die von der Stromversorgung an die Steuerung
abgegebene Energie direkt mit einem oder allen Ausgangskanälen
verbunden wird. Sie müssen dies bei der Installation berücksichtigen und
gegebenenfalls für einen geeigneten Schutz sorgen.

Die Gleichstromversorgung der Steuerung muss extern durch eine träge
Sicherung (T20AH, 50V) bis 20A gesichert sein.

Der Installationstechniker muss einen deutlich gekennzeichneten, leicht
zugänglichen Schalter als Teil der Installation in der Nähe vorsehen, mit
dem die Steuerung an beiden Stromleitern von ihrer Stromquelle getrennt
werden kann.

Durch induktive Lasten verursachte Einschaltstöße zum TR-HT müssen
extern unterdrückt werden.

Warnung:

Es handelt sich hierbei um ein Produkt der Klasse A. Die

Verwendung in Wohngebieten kann zu Funkstörungen führen und eine
solche Verwendung sollte vermieden werden, es sei denn besondere
Maßnahmen werden vom Anwender ergriffen, um die Emissionen auf ein

—

11

—

«
...
9
10
11
12
13
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: Lamtec Страницы: 22

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Mamas & Papas Страницы: 24

Бренд: Mamas & Papas Страницы: 24

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: Valco baby Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды