GARDASOFT TR-HT2 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 78

background image

TR-HT2xx LED Controller - User Manual

surcharges. Nous recommandons d'utiliser un boîtier d'alimentation qui
limite le courant de sortie de l'appareil à la valeur nominale appropriée du
contrôleur, en réglant la limite de courant sur l'alimentation (si possible) ou
via la protection contre les surcharges. Le boîtier d'alimentation doit être
approuvé selon la norme CEI 60950-1, CEI 60335-1, CEI 61010-1 ou
CEI61558-1,-2,-16. Le boîtier d'alimentation peut aussi être approuvé
selon des normes de sécurité équivalentes ou supérieures.

Tous les conducteurs sous tension dérivés depuis l'alimentation secteur
doivent aussi posséder une sortie à tension de sécurité extra-basse. Se
reporter à la Section 1, Informations de référence du TR-HT pour les
limites de tension autorisées.

Lorsqu'il atteint ses valeurs nominales maximales, le boîtier du TR-HT
peut dépasser les 65°C. Par conséquent, tout le câblage doit soit avoir
une capacité minimale de 100°C, soit être en plus isolé par une gaine
suffisamment résistante à la chaleur, soit ne pas toucher le boîtier en
métal du contrôleur ou son dissipateur thermique s'il est installé.

Le câblage d'alimentation vers le contrôleur doit avoir une capacité
minimale de 20A.

Le câblage reliant la sortie de la chaîne à la charge doit avoir une capacité
supérieure au courant de sortie maximal de la chaîne.

Si le contrôleur est mal réglé ou en cas de panne, l'énergie fournie par
l'alimentation au contrôleur peut devenir directement connectée à
n'importe quelle chaîne de sortie ou à toutes les chaînes de sortie. Vous
devez prendre en compte ce paramètre durant l'installation et si
nécessaire, fournir une protection adéquate.

L'alimentation en courant continu vers le contrôleur doit être protégée par
un fusible 20A en externe, plus précisément un fusible à action retardée
(T20AH, 50V).

Dans le cadre de l'installation, l'installateur doit fournir un interrupteur
clairement marqué, qui soit à proximité et facilement accessible, pour
permettre au contrôleur d'être déconnecté de sa source d'énergie sur les
conducteurs d'alimentation.

Les coupures causées par des charges inductives doivent être
supprimées de manière externe vers le TR-HT.

Attention:

Il s'agit d'un produit de classe A. Son utilisation en zone

résidentielle peut causer des interférences radio. Ce type d'utilisation doit
être évité, sauf si des mesures particulières sont prises par l'utilisateur
pour restreindre les émissions à un niveau qui permet la réception des
transmissions diffusées.

—

14

—

«
...
12
13
14
15
16
...
»

Содержание TR-HT2 Series















































































Отзывы:

Нет отзывов

Похожие инструкции для TR-HT2 Series

Бренд: GE Страницы: 425

Бренд: Dantherm Страницы: 96

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Бренд: IAI Страницы: 5

Бренд: Jabra Страницы: 4

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Rachio Страницы: 2

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: H-Tronic Страницы: 32

Бренд: micro-trak Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды