Galcon GalStar Скачать руководство пользователя страница 22

Страница: 22 / 107

GalStar

Instruction 1.0

3. Basic Operation

Screen Explanation:

(“Element Screen” – shows information about each program. Use the

“next/prev” or “jump” keys to access different programs.)

•

Program Status:

The options are:

NotIrr., Finish, Not.Fin

(not finished)

, Fault, Wait,

Irrig., Fert., Irr+Alr

(irri alarm),

Fert+Alr

(ferti alarm),

Wait+Al

(wait + alarm).

•

Operation Table:

The table consists of three columns: The first column contains the heading,

the other two columns show two parameters for each heading:

Wtr. (water)

: shows the amount of water “left” and “done”, according to the irrigation

program units setup, during the operation of the irrigation program.

Time:

Shows the amount of time “left” and “done”.

Fert A, B and C:

Shows the amount “required” and “done” of the fertilizer pumps

(only defined fertilizer pumps are shown).

Flow (flow rate):

Shows the “required” (nominal) and the “current” flow rates of the

irrigation program.

3.3

Programs and Sequences:

The basic programming of the controller is through the “Irrigation

Programs and Sequences”.
Press “Main”>“Head-1”>“Prgrms Sequnc” (Programs and Sequences) to access the “Irrigation
Program Information” screen (12).

Screen Explanation:

(information screen only, cannot be edited)

•

Program Status:

The options are:

N.Active, Def.Err

(definition error)

, StrtTim

(start

time)

, Condit, Ready, Act+Alr

( alarm)

, Pause, Fault, Wait, Wait+Al

(wait +

alarm)

, Irrig., Fert, Irr+Alr (

irri alarm)

, Frt+Alr.

(ferti alarm).

•

Irrigation Status:

The options are:

NotIrr.

(not irrigating)

, Finish, Not.Fin

(not finished)

Fault, Wait, Irrig., Fert., Irr+Alr

(irri alarm),

Fert+Alr

(ferti alarm),

Wait+Al

(wait + alarm).

•

Cycles Done:

The number of cycles carried out since the start of the irrigation program.

Содержание GalStar












































































































Результаты поиска

Содержание GalStar

Отзывы:

Galcon GalStar, Инструкция, Страница: 22 / 107

Результаты поиска

Содержание GalStar

Отзывы: