manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 1

www.furuno.com

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

DOPPLER SPEED LOG

Model

 DS-85

SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATION ........................................................................................... ii
EQUIPMENT LISTS........................................................................................................ iii

1. MOUNTING..............................................................................................................1-1

1.1 Display Unit........................................................................................................................1-1
1.2 Distributor Unit ...................................................................................................................1-5
1.3 Transceiver Unit.................................................................................................................1-6
1.4 Transducer.........................................................................................................................1-8
1.5 Option Unit .......................................................................................................................1-22

2. WIRING....................................................................................................................2-1

2.1 Overview ............................................................................................................................2-1
2.2 Precautions for Cable Installation ......................................................................................2-2
2.3 Display Unit........................................................................................................................2-2
2.4 Distributor Unit ...................................................................................................................2-5
2.5 Transceiver Unit...............................................................................................................2-10
2.6 Junction Box (option) .......................................................................................................2-12
2.7 Grounding ........................................................................................................................2-14

3. ADJUSTMENTS ......................................................................................................3-1

3.1 [EQUIPMENT] sub menu...................................................................................................3-3
3.2 [I/O] sub menu ...................................................................................................................3-6
3.3 [SIMULATION] sub menu ..................................................................................................3-7
3.4 [MAINTENANCE] sub menu ..............................................................................................3-8
3.5 [TEST] menu....................................................................................................................3-12
3.6 [DS-8510 DATA]/[DS-8520 DATA] sub menu..................................................................3-20
3.7 [EQUIP RESET] sub menu ..............................................................................................3-20
3.8 How to Set SFI.................................................................................................................3-20
3.9 How to Offset for Analog Port ..........................................................................................3-21

APPENDIX 1 JIS CABLE GUIDE .............................................................................AP-1
APPENDIX 2 DIGITAL INTERFACE  .......................................................................AP-2
APPENDIX 3 CALIBRATION....................................................................................AP-7

PACKING LISTS ......................................................................................................... A-1
OUTLINE DRAWINGS ................................................................................................ D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды