manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 7

1-1

1.

MOUNTING

1.1

Display Unit

The display unit (main or sub) can be installed on a desktop, overhead, on the bulk-
head or flush mounted in a console or panel.

1.1.1

Installation considerations

When selecting a mounting location for the display unit, keep the following in mind:

•  Keep the unit out of direct sunlight.
•  The temperature and humidity of the mounting location should be moderate and 

stable.

•  Locate the unit away from exhaust pipes and vents.
•  The mounting location should be well ventilated.
•  Mount the unit where shock and vibration are minimal.
•  Keep the unit away from electromagnetic field-generating equipment such as mo-

tors and generators.

•  For maintenance and checking purposes, leave sufficient space at the sides and 

rear of the unit and leave slack in cables. Refer to the outline drawings at the back 
of this manual.

•  A magnetic compass will be affected if the display unit is too close to it. Observe the 

compass safe distances to prevent disturbance to the magnetic compass. Refer to 
the compass safety distances of the units on "SAFETY INSTRUCTIONS" page.

•  For flush mounting in a panel, the mounting surface must be flat. Do not install the 

unit on an uneven surface.

•  To avoid damage to the cabling when mounting the display unit, make sure the ca-

bling is not excessively bent.

Note: 

The cabling to the display unit should be completed before mounting the unit. 

See section 2.3.2.

NOTICE

Do not apply paint, anti-corrosive sealant

 

or contact 

spray to coating or plastic parts of the equipment. 

Those items contain organic solvents that can damage 
coating and plastic parts, especially plastic connectors.

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды