Furuno DS-8500 Скачать руководство пользователя страница 9

Страница: 9 / 94

1. MOUNTING

1-3

2. Fit the cable gasket to the cable clamp, referring to the figure below.

3. Pass the cabling through the cable gasket and cable clamp.

Note:

To maintain the IPX5 waterproof rating, the cable must be TTYCSLA-4 (or

equivalent) with a diameter of

14.4±0.4 mm.

4. Fit the cover gasket to the rear of the display

unit. Make sure the cover gasket is placed in-
side the groove indicated in the figure below.

5. Connect the cabling to the display unit, referring to section 2.3.2.
6. Slide the cable clamp along the cable until the clamp is flush against the rear of

the display unit.

Note:

The cable clamp must be oriented with

the dome-side up, to prevent water intrusion.

7. Fasten the four screws removed at step 1.
8. Secure the cabling to the cable clamp with cable ties (local supply) referring to the

figure in section 2.3.2.

1.1.4

How to install the display unit on a desktop or overhead

The display unit is shipped with the hanger.

1. Place the display unit on a firm, flat surface, then unfasten the two knobs on either

side of the display unit to separate the display unit and hanger.

2. Drill four holes for the self-tapping screws (

20) at the installation location.

Fixing lip

Cable clamp

Cable gasket

1. Fit the cable gasket to the cable clamp,

passing the fixing lip partially through
the cable clamp.

2. To pass the fixing lip completely

through the cable gasket, twist the
cable gasket gently.

3. Check that the cable gasket is flush

against the cable clamp, as shown
below.

4. Check that the cable gasket’s fixing

lip is flush against the inside of the
cable clamp.

Fixing lip

WAGO lever

Groove for
cover gasket

Dome

Cable
clamp

Содержание DS-8500































































































Результаты поиска

Содержание DS-8500

Отзывы:

Бренды по названию

Популярные бренды

Furuno DS-8500, Руководство по установке

Результаты поиска

Содержание DS-8500

Отзывы:

Бренды по названию

Популярные бренды