manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 14

1.  MOUNTING

1-8

1.4

Transducer

The performance of this equipment is directly dependent on the installation of the 
transducer. The installation of the transducer and the tank should be accomplished by 
a dockyard referring to the installation drawings at the back of this manual.

Also, the transducer DS-820 which is used for DS-80 is available. For installation of 
DS-820, see the installation manual (IME-72470) for DS-80.

1.4.1

Installation considerations

To decide the location of the transducer, the following points should be taken into ac-
count.

•  Locate the transducer DS-8530 at least 2.5 m from the transducer of an echo 

sounder.

Transducer, mounting location

•  Separate as far as possible from air bubble sources; e.g., side thruster and water 

disposal pipes.

•  The Doppler speed log emits ultrasonic waves diagonally forward and backward, so 

the transducer should not be located on the same line of the Doppler speed log in 
the bow-stern direction.

•  Install in close proximity to the keel, for uniform water flow.

The closer the ship is to the keel line, the more the water flow at the bottom of the 
vessel creates an arrhythmic flow parallel to the keel, thus reducing errors in speed 
measurement.

•  Generally, best performance is obtained by mounting on the bow; the stern side is 

influenced more easily by air bubbles and propeller cavitation.

•  Never apply ordinary ship bottom paint to the transducer face. Whenever the ship 

is dry docked, the transducer face should be cleaned, removing marine life and for-
eign material.

•  For DS-784 (flush type), DS-786 (gate valve type) or DS-854 (ball valve type) trans-

ducer tank, remove the hose clamp of the transducer.
For DS-781 (projection type), the hose clamp is required even if it is removed tem-
porarily under installation.

•  Do not remove the metal pipe on the outside of the transducer. Please mount the 

transducer with the metal pipe attached to prevent reverberation.

STERN

BOW

2500 mm or more

Recommended location for 
echo sounder transducer 

ECHO SOUNDER TRANSDUCER
(a or b)

DOPPLER SPEED LOG TRANSDUCER

a

c

b

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды