manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 50

3.  ADJUSTMENTS

3-6

3.2

[I/O] sub menu

On the main menu, select [EQUIPMENT] 

→

[I/O] to open the [I/O] sub menu.

3.2.1

[ALERT MODE] menu

On the [I/O] sub menu, select [ALERT 
MODE] to set the alert mode, [LEGACY], 
[ALERT I/F1] , [ALERT I/F2] and [ALERT 
I/F3](default: [ALERT I/F1]).

3.2.2

[CH1], [CH2] menu

On the [I/O] sub menu, select [CH1] (or 
[CH2]) to set each channel setting. 
These channels can be set for the follow-
ing signals.

[CH1]: RD1, TD1

[CH2]: RD2, TD2 to TD8

[INPUT FORMAT]

Select the input format, [IEC] or [NMEA] (default: [IEC]).

[OUTPUT FORMAT]

Select the output format, [IEC Ed.1] to [IEC Ed.5] (default: [IEC Ed.5]).

[BAUD RATE]

Select the baud rate, [4800] bps or [38400] bps (default: [4800] bps).

Note: 

For [CH2], baud rate is fixed at [4800].

3.2.3

[LAN] menu

On the [I/O] sub menu, select [LAN] to 
set LAN setting.

[EQUIPMENT] sub menu

Option menus

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды