manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 46

3.  ADJUSTMENTS

3-2

How to select the language for menu window

The default language for the menu window is English. To change the language to Jap-
anese, set as follows.

1. Press the 

MENU/ESC

 key to open the main menu.

2. Select [DISPLAY] then press the 

ENT

 key.

3. Select [LANGUAGE] then press the 

ENT

 key.

4. Select the appropriate language (English or Japanese) then 

ENT

 key.

5. Press the 

DISP

 key to close the menu window.

How to Open the [EQUIPMENT] menu for installation

Note: 

For “MAIN” display unit only, the installation menus are operative. Make sure 

that [M] (Main) is shown at the top of display.

1. Press the 

Power

 key to turn on the unit.

2. Press the 

MENU/ESC

 key to open the main menu. The [SERVICE] menu is 

shown in gray and inoperative.

3. Select [EQUIPMENT] then the password input window for the [EQUPMENT] 

menu is shown.

[MENU]→[DISP]→[BRILL] key

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды