manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 15

1.  MOUNTING

1-9

•  Refer to the procedure below for the location where the supplied liquid gasket 

TB1121 is applied. For DS-781 (projection type) bottom tank, there is no place to 
apply the liquid gasket.

1.4.2

How to install the transducer

DS-784 (Mounting of Flush Type Seachest)

The seachest DS-784 is delivered temporarily assembled with the transducer.

1. Loosen lock nut (5) with a wrench (hex. size: 

50 mm) and take off cap nut (4) from top cover 
(3) together with gasket (6) and flat washer 
(7). (It is not necessary to draw the cap nut 
completely out from the cable.)

2. Unscrew hex. socket head bolts (9) (M12

×

25, 

4 pcs.) with a socket screw wrench (size: 10 
mm). Separate the seachest (2) and transduc-
er (1) from top cover (3). Handle O-ring (8) 
carefully.

3. Align the "FORE" mark on the side of the 

seachest to face the fore direction, parallel 
with the fore-aft line of the ship (a 1 degree er-
ror margin is allowed), then weld the seachest 
to the hull plate. The seachest should also be 
level with ship’s normal trim within 1 degree.

4. Finish the outside hull plate with a grinder to 

ensure smooth water-flow.

5. Apply “Kinoruster (Anti-crevice corrosive seal-

ant)” to face A of the seachest (2), O-ring 
groove on the hull flange, O-ring (8) and face 
A of the stop cover (3).

6. Fit O-ring (8) onto the O-ring groove.
7. Place transducer (1) into the seachest (2) so 

that the alignment nipple on the transducer face fits into the notch on the hull 
flange.

8. Clean the hull flange face with a clean cloth and fit the stop cover (3) on the hull 

flange.

9. Tighten hex. socket bolts (9) with a socket screw wrench.
10. Fit the gasket (6) and flat washer (7) over the transducer flange and tighten cap 

nut (4) securely with a wrench (hex. size: 50 mm). Screw lock nut (5).

11. When running the transducer cable inside the conduit pipe, screw the pipe onto 

the cap nut (PS3/4) for watertightness.

Note: 

Never remove the four flat head screws on the transducer. These are sealing 

screws and are required to maintain watertightness.

See Note.

(4)

(5)

(4)

(7)

(6)

(9)

(10)

(3)

(1)

(8)

(2)

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды