Furuno DS-8500 Скачать руководство пользователя страница 60

Страница: 60 / 94

3. ADJUSTMENTS

3-16

[DS-8510 TEST (3/3)]: page 3

3.5.3

DS-8520 TEST

The test result of Transceiver Unit DS-8520, the equipment information, ROM/RAM
test results or serial port test result etc., is shown on this menu. The test result has
three pages.

[DS-8520 TEST (1/3)]: page 1

[IN-
TER-
NAL
TEM-
PER
ATU
RE]

Temperature for board of distributor unit

[-99.9] to [999.9] (°C)

[5 VOLT]

Voltage of 5 V for distributor unit

[0.0] to [99.9]

[12 VOLT]

Voltage of 12 V for distributor unit

[0.0] to [99.9]

key

Go to page 3 of the [DS-8510 TEST].

MENU/ESC

key

Go back to [TEST] sub menu.

Item

Meaning

Range

[

SIO

]: SIO communication test

[CH1]

Result of CH1 communication test

[OK] or blank

[CH2]

Result of CH2 communication test

[OK] or blank

[DS-8520]

Result of transceiver unit communication

[OK] or blank

[MAIN]

Result of MAIN communication

[OK] or blank

[SUB1]

Result of SUB1 communication

[OK] or blank

[SUB2]

Result of SUB2 communication

[OK] or blank

[RD-502]

Result of RD-502 communication

[OK] or blank

[

USB

]: USB communication test

[USB R/W]

Check if reading or writing to USB

[OK] or blank

MENU/ESC

key

Go back to [TEST] sub menu.

Item

Meaning

Range

XXXXXXX-01.01 (20XX1213)
XXXXXXX-01.01 (20XX1213)
XXXXXXX-01.01 (20XX1213)
XXXXXXX-01.01 (20XX1213)
XXXXXXX-01.01 (20XX1213)

123

A
B

Содержание DS-8500































































































Результаты поиска

Содержание DS-8500

Отзывы:

Бренды по названию

Популярные бренды

Furuno DS-8500, Руководство по установке

Результаты поиска

Содержание DS-8500

Отзывы:

Бренды по названию

Популярные бренды