manualshive.com logo in svg

Furuno DS-8500, Руководство по установке

Поделиться
Скачать
Furuno DS-8500 Скачать руководство пользователя страница 56

3.  ADJUSTMENTS

3-12

•  [FORE], [AFT]: Show the ship’s speed/direction and signal level which the transduc-

er of FORE (or AFT) outputs. When an analog circuit activates properly, the signal 
level is 35 to 40 dBuV. This value is updated every second. Ship direction is indicat-
ed as follows: [

↑

] means “Go forward” and [

↓

] means “Go afterward”.

[LAN ERROR COUNTER]

This screen is to show the error status of LAN connection. To go [MAINTENANCE] 
window, press the 

MENU/ESC

 key.

•  [UDP CHECKSUM ERROR]: Number of checksum errors in UDP headers.
•  [INVALID HEADER]: Number of "UdPbC<NULL>" errors at the beginning of sen-

tences.

•  [INCORRECT TAG BLOCK]: Number of tag block structural errors.
•  [TAG BLOCK CHECKSUM ERROR]: Number of checksum errors at the end of tag 

blocks.

•  [TAG BLOCK SYNTAX ERROR]: Number of tag block format errors.
•  [TAG BLOCK FRAMING ERROR]: Number of sentences with unexpected starts/

stops in the tag block.

•  [INCORRECT SENTENCE]: Number of sentences in tag block with checksum er-

rors or other errors.

3.5

[TEST] menu

On the main menu, select [EQUIPMENT] 

→

[TEST] to open the option menus of 

[TEST] sub menu.

3.5.1

[DS-8500 TEST] menu

The test result of Display Unit DS-8500, the equipment information, ROM/RAM test or 
serial port test etc., is shown on this menu. The test result has four pages.

0
0
0
0
0
0
0

[EQUIPMENT] sub menu

Option menus

Содержание DS-8500































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды