Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 96

Страница: 96 / 344

2. Mount the disk image of the RHEL distribution DVD on remote storage.

3. Change the boot order to give the highest priority to booting the storage unit where the operating system is

installed.

For details, see 1.3.1 [Power Control] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-

E110EN).

4.3.3

Installing the operating system

This section describes the operating system installation with SVIM.

SVIM can perform the following types of operating system installation. For the procedure for each mode, see the

ServerView Suite ServerView Installation Manager

TABLE 4.2 Operating system installation by SVIM

Mode

Functional outline

Remarks

Quick mode

You can simply use the minimum settings

necessary for operating system installation.

This mode uses Fujitsu's recommended

settings.

Use this mode to readily install the OS.

Guide mode

You can specify setup information by

following the instructions of the wizard.

You can save the specified information in a

configuration file for use during

reinstallation.

This mode enables detailed settings.

Use the mode if you want to configure

installation with detailed RAID and

OS settings.

All screenshots are display examples, and the actually displayed contents vary depending on the system

configuration and other factors.

Operations

1. Make the setting for booting the partition from remote storage.

For details on the setting, see 1.6.3 Remote operation (BMC) in the

PRIMEQUEST 1000 Series

Administration Manual

(C122-E108EN).

2. Insert ServerView Suite DVD1 into the DVD drive. Then, power on the partition.

Remarks

You can boot from the DVD drive either by selecting [Force boot from DVD] from [Boot Selector], or by

specifying the DVD drive as the highest-priority device to boot from, in UEFI mode.

If the operating system supports UEFI mode, you can install it in UEFI mode by using the following procedure

to change the boot order.

1. After powering on the partition, press and hold down any key ([Space] key, for example) other than

the [Enter] key while the FUJITSU logo is displayed, to display the Boot Manager Front Page.

2. Select the following items from the menu in the order given in the Boot Manager Front Page:

[Boot Maintenance Manager] - [Boot Options] - [Change Boot Order] - [Change the order]

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды