Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 158

Страница: 158 / 344

- Operations management software cannot collect information on the partition side.

- Even under an REMCS agreement, no software errors are reported.

- Hot maintenance of hard disks is disabled. The partition must be stopped for maintenance.

- PRIMECLUSTER linkage is disabled.

Remarks

- SVIM installs PSA as it installs the operating system. For details on SVIM, see the

ServerView Suite

ServerView Installation Manager

- For details on how to manually install PSA, see

APPENDIX B Manual PSA Installation and

Uninstallation

- The following table lists settings for PSA operation. The installer automatically adds or updates these settings

during PSA installation.

TABLE 6.3 Settings automatically added/changed during PSA installation

Target

Action

Remarks

syslog.conf file

Add setting

snmpd.conf file

Add setting

snmptrapd.conf file

Add setting

services files

Add setting

Added port: The installer does not check for

duplicate port numbers when a setting is added to

the fj-webgate (24450) services file. Change

settings as needed.

snmptrapd start option

Change

snmpd start option

Change

Dedicated PSA-to-MMB

communication LAN interface

Set IP address

Referring to

6.2.1 Configuring the PSA-to-MMB

communication LAN

, change settings as needed.

iptables setting

Add setting

SELinux configuration file

(/etc/selinux/config)

Change

SELinux is disabled only for RHEL5. If SELinux

is disabled, do not change the settings.

SELinux setting

Add setting

The policy module is added for RHEL6 or later

only.

Note

If you change the IP address of the dedicated PSA-to-MMB communication LAN on the MMB side or partition

side, you need to then restart PSA. Otherwise, a display error may occur in the [PSA] window of the MMB Web-

UI. Moreover, PSA would not be able to report any detected errors.

6.2.1

Configuring the PSA-to-MMB communication LAN

This section describes how to confirm the settings for the PSA-to-MMB communication LAN.

Communication between PSA and the MMB requires an active NIC (network interface card) connected to the PSA-

to-MMB communication LAN.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

130

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды