Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 110

Страница: 110 / 344

4.5

Windows Installation Procedures on the Built-in HDD

This section concisely describes the procedures for installing Windows on the built-in HDD. Confirm the MMB

configuration and successful login to the MMB before starting the installation.For details on configuring the SAN

storage unit and FC card (Fibre Channel card), see the

PRIMEQUEST 1000 Series SAN Boot Environment

Configuration Manual

(C122-E155EN).

4.5.1

Advance setup

Set up the following as needed.

1. Remove each built-in HDD that is not the installation destination.

2. Confirm the partition settings with the MMB.

- Setting the SB/IOB/GSPB configuration

(See

3.4.1 Setting a partition configuration

- Configuring Console Redirection

(See

3.4.6 Configuring Console Redirection

- Video redirection: Enable

- Remote storage: Enable

- Console redirection: Enable

- Setting various modes

(See

3.4.5 Setting various modes

3. Assign I/O spaces to the SAS card, SAS array controller card, Onboard SAS controller (GSPB), SAS disk

unit controller and SAS array disk unit controller.

For details on I/O space assignment, see 3.4.5 Setting various modes in this manual and 5.5.1 [Configure I/

O Space Assignment] menu in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

4.5.2

Preparing for Installation

Prepare the following.

1. Prepare the following disk image:

Windows operating system media

2. Disconnect all the FC cables.

3. Mount the disk image through a video redirection connection.

4. Change the boot order so that DVD booting has the highest priority.

For details, see 1.3.1 [Power Control] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-

E110EN).

4.5.3

Installing the operating system

This section describes the operating system installation with SVIM.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды