Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 52

Страница: 52 / 344

FIGURE 3.3 Network configuration and IP addresses of the management LAN

Connect the management (USER) ports of MMB#0 and MMB#1 to an external switching hub with LAN cables.

At this time, also connect the MMB console PC to the external switching hub. The MMB console PC is used for

MMB Web-UI operations.

Set the physical IP addresses and virtual IP addresses of MMB#0 and MMB#1 in the same subnet.

Each MMB has the following two addresses:

- Physical IP address (in the above figure, MMB#0 = 192.168.1.100, MMB#1 = 192.168.1.101)

- Virtual IP address (in the above figure, 192.168.1.102)

An external connection (e.g., Web browser, maintenance terminal, REMCS) uses the virtual IP address for

communication.

TABLE 3.4 Required settings for external LAN connections

Condition

Required setting

The external switch used in the

configuration is a switching hub that

supports functions preventing cycling

(e.g., Spanning Tree Protocol,

Domain Separation).

Select [disable] for the spanning tree protocol of the ports of the

switching hub and main unit. Alternatively, set domain separation

to on to disable the functions preventing cycling.

Configuration that meets any of the

following conditions:

- The send destination server

becomes an external server

through the firewall.

- It uses a mail server that

restricts IP addresses.

The firewall or mail server settings must permit packets with the

physical IP address of MMB#0 or MMB#1 to pass.

REMCS connection

The connection patterns are as follows:

- Internet connection:

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды