Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 151

Страница: 151 / 344

5.7

Configuring Service Life Monitoring by RAS Support Service

For the use of RAID cards and UPSs, configure the BBU (Battery Backup Unit) service life monitoring by RAS

Support Service.

SVIM automatically installs the RAS Support Service. For details on the manual installation and service life

monitoring setting procedures for RAS Support Service, see the

RAS Support Service User's Guide (for Linux or

Windows)

For details on SVIM, see the

ServerView Installation Manager

5.7.1

BBU service life monitoring for a RAID card

The BBU on a RAID card is a service life component. RAS Support Service performs service life monitoring.

When starting, RAS Support Service checks for the RAID cards that have a BBU in order of PCI bus number,

according to ServerView RAID information. It will monitor those RAID cards.

RAS Support Service performs service life monitoring and sends messages for replacement notification at the

following times.

TABLE 5.2 Message for advance notification of replacement and replacement notification message
(RAID card)

Start time for sending messages for advance notification

of replacement

Time for sending replacement notification

message

After about 2 years from the start of use or replacement

of the battery unit

After about 3 years

Operations

1. Start the GUI of RAS Support Service.

- Windows: Log in to the operating system. Start the GUI.

- Linux: Open a Web browser. Access the specified URL. Log in.

For details on operations, see the

RAS Support Service User's Guide (for Linux or Windows)

2. The Service Life Component Names list on the Component Service Life Information and Settings screen of

RAS Support Service displays [Battery (RAID_Card#xx)] in order of PCI bus number.

You can enter a value (for a RAID card) in the Mounting Dates list to enable battery service life monitoring.

In the Mounting Dates list, enter the mounting dates of the RAID cards for which to set service life monitoring.

Notes

Note the following points about BBU service life monitoring for a RAID card in the PRIMEQUEST 1800E2.

- Of the mounted RAID cards shown in

FIGURE 5.3 RAS Support Service screens (no BBU)

, the RAID card

without a BBU is not monitored by RAS Support Service.

FIGURE 5.3 RAS Support Service screens (no BBU)

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 5 Work after Operating System Installation (PRIMEQUEST 1800E2)

123

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды