Fujitsu F2MC-8L F202RA Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 436

background image

27

CHAPTER 3 CPU

3.2

Dedicated Register

The dedicated register in the CPU consists of a program counter (PC), two arithmetic
operation registers (A and T), three address pointers (IX, EP, and SP), and program
status (PS) register. The size of each register is 16 bits.

■

Dedicated Register Configuration

The dedicated register in the CPU consists of seven 16-bit registers. Some registers allow only the lower 8

bits to be used.

Figure 3.2-1 shows the configuration of the dedicated register.

Figure 3.2-1 Configuration of Dedicated Register

■

Functions of the Dedicated Register

●

Program counter (PC)

The size of the program counter is 16 bits. It indicates the memory address at which the CPU is currently

handling an instruction. The program counter is updated with an instruction executed, interrupt, or reset.

The initial value specified after the reset operation is the mode data read address (FFFD

H

).

●

Accumulator (A)

The accumulator is a 16-bit arithmetic operation register. It handles arithmetic operations or data transfer

using data on memory or data in another register such as temporary accumulator (T). The accumulator

allows data in it to be used as a word (16 bits) or bytes (8 bits). When arithmetic operations or data transfer

is handled in the unit of a byte, only the lower 8 bits (AL) of the accumulator are used; the upper 8 bits

(AH) remain unchanged. The initial value specified after the reset operation is undefined.

16 bits

:

A

:

T

:

IX

:

EP

:

SP

:

RP

CCR

:

PS

PC

Initial value

FFFD

H

Undefined

Undefined

Undefined

Undefined

Undefined

Program counter

Indicates the current instruction stored position.

Accumulator

Temporary register that handles arithmetic operations and

data transfer.

Temporary accumulator

Handles arithmetic operations together with the accumulator.

Index register

Indicates index address.

Extra-pointer

Indicates memory address.

Stack pointer

Indicates the current position in the stack.

Program status register

Stores the register bank pointer and condition code.

Flag I = 0
IL1 and IL0 = 11
The other bits are undefined.

«
...
41
42
43
44
45
...
»

Содержание F2MC-8L F202RA





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2MC-8L F202RA

Бренд: 3Com Страницы: 20

Бренд: Black Box Страницы: 9

Бренд: Supero Страницы: 68

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренд: Caen Страницы: 14

Бренд: AXIOMTEK Страницы: 58

Бренд: Compro Technology Страницы: 2

Бренд: ZALMAN Страницы: 16

Бренд: Aleratec Страницы: 16

Бренд: Jabra Страницы: 2

Бренд: Vivotek Страницы: 185

Бренд: ADTRAN Страницы: 4

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

Бренд: Curtiss-Wright Страницы: 10

Бренд: Curtiss-Wright Страницы: 59

Бренд: COP-USA Страницы: 114

DM/V480A-2T1-PCI

Бренд: Dialogic Страницы: 2

Бренд: dbx Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды