Fujitsu F2MC-8L F202RA Скачать руководство пользователя страница 278

Страница: 278 / 436

262

CHAPTER 12 A/D CONVERTER

●

Clock selector

The clock selector selects the clock to be used to activate A/D conversion while continuous activation is

enabled (ADC2: EXT = 1).

●

Analog channel selector

This circuit selects one out of the eight analog inputs.

●

Sample hold circuit

This circuit holds the input voltage selected by the analog channel selector. By performing the sample hold

of the voltage input immediately after the activation of A/D conversion, A/D conversion can be performed

without the variance of the input voltage affecting it during A/D conversion (during comparison).

●

D/A converter

This generates the voltage that corresponds to the values set in the ADDH and ADDL registers.

●

Comparator

This compares the input voltage for which sample hold is performed, with the output voltage of the D/A

converter to determine which is the greater of the two.

●

Control circuit

The control circuit has the following function.

•

For A/D conversion functions, this circuit determines the values in turn from the MSB in the 10-bit A/D

data register toward the LSB based on the large and small signals from the comparator. When the

conversion is completed, it sets the interrupt request flag bit (ADC1: ADI).

●

A/D data register (ADDH and ADDL)

The high-order 2 bits of 10-bit A/D data are stored in the ADDH register. The low-order 8 bits of 10-bit

A/D data are stored in the ADDL register.

The ADDH and ADDL registers have the following function.

•

For A/D conversion function, these registers store the results of A/D conversion.

●

A/D control register 1 (ADC1)

This register is used to enable and disable functions, select an analog input, check statuses, and control

interrupts.

●

A/D control register 2 (ADC2)

This register is used to select an input clock, enable and disable interrupts, select functions, and perform

other activities.

●

Interrupts of the A/D converter

When the set conditions are satisfied at the completion of A/D conversion for IRQ8, if an interrupt request

output is enabled (ADC2: ADIE = 1), an interrupt request occurs.

Содержание F2MC-8L F202RA





















































































































































































































































































































































































































































Результаты поиска

Содержание F2MC-8L F202RA

Отзывы:

Похожие инструкции для F2MC-8L F202RA

Бренды по названию

Популярные бренды

Fujitsu F2MC-8L F202RA, Руководство по оборудованию

Результаты поиска

Содержание F2MC-8L F202RA

Отзывы:

Похожие инструкции для F2MC-8L F202RA

Бренды по названию

Популярные бренды