manualshive.com logo in svg

Fujitsu AB* A12GATH, Руководство по обслуживанию

Поделиться
Скачать
Fujitsu AB* A12GATH Скачать руководство пользователя страница 7

01-02

Execution

Perform the auto address setting of Signal amp. at first, and the next perform the auto-
 address setting of indoor unit.  
When you perform the autoaddress setting for the indoor unit address setting
 needs to be done at first.

Pre-commisioning

"Before Power ON"

Gas leak test

Use an R410A dedicated leak tester to check for gas leaks.

1

2

3

Confirm the additional refrigerant amount with the installation

 manual, etc.

Always take the R410A refrigerant from the cylinder liquid phase

 and charge it using the gas phase.

(Do not lay a cylinder with siphon pipe on its side.)

Use an R410A dedicated gauge manifold and charging hose.

If taken from the air phase, since the 
composition of the refrigerant which is 
charged will change, low performance 
and abnormal stop will occur easily.
Prevent erroneous sealing in of 
refrigerant.

A leak tester for other than R410A 
cannot detect leaks.

Handover & explanation of operation

In case of  "Auto Address setting"

Test run & adjustment

Addition refrigerant charging

1
2
3

Power source installation inspection
Field setting and setting inspection
Transmission wire installation inspection

4 Piping installation inspection

Before starting the installed system,
the final inspection is necessary.
When you find out any incorrect install-
 ation or wrong setting, revise it before
 starting the system

Pre-commisioning

"After Power ON"

1
2
3

Connect Service Tool
Power source inspection 
Error indication inspection

4 Transmission wire connection inspection

When you see any abnormal things,
 turn OFF the power supply first, and 
 revise it with power OFF state.

Note : 

Other Field setting with power ON state, and adjustment

Check operating condition by using service tool.

For the judgment of operating condition, refer to the operation check 

sheet.

When you see any abnormal things,
stop the system, and revise it with 
power OFF state.

Содержание AB* A12GATH


















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды