Fujitsu AB* A12GATH Скачать руководство пользователя страница 169

Страница: 169 / 241

Trouble shooting 84 E59. 2

INDOOR UNIT Error Method:

Indoor Unit Fan Motor 2 rotation

speed Error

Indicate or Display:
Outdoor Unit : E.5 U.1

Error Code : 5 9, 5 9. 2

Detective Actuators:

Indoor Unit Controller PCB Circuit

Indoor Fan Motor 2

Detective details:

When the FAN motor feed back rotation value which is detecting on the

controller PCB becomes 0 and lasts for more than 1 minute

at motor operation condition.

Or, when the feed back rotation value contimues at 1/ 3 of target value

for more than 1 minute.

Check Point 2 : Check Motor winding / Internal PCB circuit

Check Indoor Fan motor

( Refer to the PARTS INFORMATION 19, 20)

>>If Fan motor is abnormal, replace it.

Check Point 1 : Check rotation of Fan

Rotate the fan by hand when operation is off.

(Check if fan is caught, dropped off or locked motor)

>>If Fan or Bearing is abnormal, replace it.

Check Point 3 : Check ambient temp. around motor

Check excessively high temperature around the motor.

(If there is any surrounding equipment that causes heat)

>>Upon the temperature coming down, restart operation.

Check Point 4 : Check Motor Capacitor

Check continuity of motor capacitor

>>If it is shorted, replace the capacitor.

Check Point 5 : Replace Controller PCB

Forecast of Cause :

1. Fan rotation failure 2. Fan motor winding open 3. Motor protection by ambient temp. increase

4. Capacitor failure 5. Controller PCB failure

Change Controller PCB and set up the original address.

04-93

Содержание AB* A12GATH


















































































































































































































































Результаты поиска

Содержание AB* A12GATH

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu AB* A12GATH, Руководство по обслуживанию

Результаты поиска

Содержание AB* A12GATH

Отзывы:

Бренды по названию

Популярные бренды