Fujitsu AB* A12GATH Скачать руководство пользователя страница 156

Страница: 156 / 241

Trouble shooting 68 EAC. 4

OUTDOOR UNIT Error Method:
Outdoor unit Heat Sink Tempreture

Abnormal

Indicate or Display:

Detective Actuators:

Detective details:

Forecast of Cause :

Check Point 1 : Check the heat sink state

1. Foreign matter on heat sink, heat sink dirty

2. Foreign matter on heat exchanger, excessive ambient temperature rise

3. Heat sink temp. sensor defective

Heat sink temp. sensor

"Protection stop by

"heat sink temp. 91°C (195.8°F) " occurred 3 times within 60 minutes.

Heat sink temp. sensor characteristics check

(Check by disconnecting sensor from PCB.)
* For the characteristics of the thermistor, refer to "Service Parts Information 24".

Check Point 3 : Check the heat sink temp. sensor

Heat sink foreign matter, soiling check

Heat exchange foreign matter check
Ambient temperature not raised by effect of other heat sources?
Discharged air not sucked in?

Check Point 2 :

Check the foreign matter and ambient temperature of heat exchanger

Indoor Unit : Operation LED 9 times Flash, Timer LED 15 Times Flash,

Filter LED Continuous Flash.

Outdoor Unit : E. A C. 4

Error Code : 9 U / A C

Caution

By changing of DIP SW 4-2 to ON, the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

(Stand alone outdoor unit is impossible)

The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

- The operating compressor life time becomes shorter.

- The operating performance may drop due to the limited active compressor(s).

- The compressor may stop frequently by protection controlling.

*In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

04-80

Содержание AB* A12GATH


















































































































































































































































Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды

Fujitsu AB* A12GATH, Руководство по обслуживанию

Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды