manualshive.com logo in svg

Fujitsu AB* A12GATH, Руководство по обслуживанию

Поделиться
Скачать
Fujitsu AB* A12GATH Скачать руководство пользователя страница 165

Trouble shooting  80

Outdoor air unit- No Power

Forecast of  Cause :

1. Power Supply failure

2. Outside cause  

3. Electrical Component defective 

Is not the breaker down?

Check Point 1 : Power supply

Instant drop  -----Check if there is a large load electric apparatus in the same circuit.

Momentary power failure ----- Check if there is a defective contact or leak current in the power supply circuit. 

Noise ----- Check if there is any equipment causing harmonic wave near electric line 

(Neon bulb or electric equipment that may cause harmonic wave).

Check the complete insulation of grounding.

OK 

Check protector open / short

If the protector is open circuit, replace it.

Check Point 2 : Check Protector (20A) 

04-89

OK (No short circuit)

Check AC line (L-N) open / short

Check Point 3 : Check AC line

NG (Short circuit)

Disconnect  the wire between Filter PCB and reactor,

check short circuit of AC line.  

If there is short circuit, replace the Filter PCB. 

Check Point 4 : Check short circuit Filter PCB

OK (No short circuit)

Connect the disconnected wire(s) on the check point 4,  

disconnect  the wire between Diode bridge and Capacitor,

check short circuit of AC line.  

If there is short circuit, replace the Diode bridge.

Check Point 5  : Check short circuit Diode bridge

OK (No short circuit)

Connect the disconnected wire(s) on the check point 5,  

disconnect  the wire between Capacitor and Filter PCB,

check short circuit of AC line.  

If there is short circuit, replace the Capacitor.

Check Point 6 : Check short circuit Capacitor

OK (No short circuit)

Connect the disconnected wire(s) on the check point 6,  

disconnect  the wire of Fan motor, check short circuit of 

AC line.  

If there is short circuit, replace the Power supply PCB.

Check Point 7 : 

Check short circuit Power supply PCB

OK (No short circuit)

Check open / short of FAN motor

Refer to the Service Parts Information 20.

If there is short circuit, replace FAN motor.

Check Point 8 : Check Fan Motor

Disconnect the connector (CN200) on the Power supply PCB 

and check the short circuit 

1. DC12V line  ( CN200 Pin 1- 5 ) 

2. DC 5V Line ( CN200 Pin 1 - 3 )

3. DC 15V-1 Line ( CN500 Pin 3 - 4 )

4. DC 15V-2 Line ( CN530 Pin 3 - 4 )

If one of them is short circuit, replace the Power supply PCB

Check Point 9 : Short circuit check on DC circuit

Disconnect the CN10 (EEV1)  on the Main PCB, and check short circuit 

on Main PCB CN 4 Pin 1 - 5.

If the short circuit disappears, replace the EEV coil.

  

Check Point 10 : Check short circuit of actuators (for DC12V)

Disconnect the CNC01 (WRC) on the Main PCB, and check short circuit 

on Main PCB CN 4 Pin 1 - 5.

If the short circuit disappears, check the WRC wire, WRC.  

Disconnect the CNB01 (Ext.Out) on the Main PCB, and check short circuit 

 on Main PCB CN 4 Pin 1 - 5.

 If the short circuit disappears, check the Ext. device or wiring.  

Disconnect the CN2 (TransmissionPCB)  on the Main PCB, and check 

short circuit on Main PCB CN 4 Pin 1 - 5.

If the short circuit disappears, replace the Transmission PCB.

  Disconnect the CN22 (Interconnecting wire) on the Main PCB, and check 

short circuit on Main PCB CN 4 Pin 1 - 5.

If the short circuit disappears, replace the Filter PCB.

  If the short circuit appears after disconnecing actuators, 

replace the Main PCB.

Disconnect the CN14 (SW PCB) on the Main PCB, and check short circuit

 on Main PCB CN 4 Pin 1 - 3.

If the short circuit disappears, replace the SW PCB.

  

Check Point 11 : Check short circuit of actuators (for DC5V) 

Disconnect the CN18 (Receiver unit *Option) on the Main PCB, and check

 short circuit on Main PCB CN 4 Pin 1 - 3.

If the short circuit disappears, check the wire, Receiver unit.  

Disconnect the CN2 (Transmission PCB)  on the Main PCB, and check 

short circuit on Main PCB CN 4 Pin 1 - 3.

If the short circuit disappears, replace the Transmission PCB.

  Disconnect the CN21 (Interconnecting wire) on the Main PCB, and check 

short circuit on Main PCB CN 4 Pin 1 - 3.

If the short circuit disappears, replace the Power supply PCB.

  If the short circuit appears after disconnecing actuators, 

replace the Main PCB.

OK (No short circuit)

OK (No short circuit)

OK (No short circuit)

Содержание AB* A12GATH


















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды