Fujitsu AB* A12GATH Скачать руководство пользователя страница 116

Страница: 116 / 241

Inverters Communication Error

YES

Outdoor unit Main PCB

Check Point 2 : Check the main PCB to Inverter PCB wiring

Connector connection state check
Cable open check

Check Point 3 : Check Main PCB

Chack Main PCB. (Refer to "Service Parts Information 3, 4")

1. Noise 2. Main PCB to Inverter PCB wiring connection defective

3. Main PCB defective 4. Inverter PCB defective

Check Point 4 : Replace Inverter PCB

Replace Inverter PCB.

Check if ground is connection correctly or there are no related cables near

the power line.

Check Point 1-1 :

Turn the power on again

Error displayed again?

Check Point 1-2 : Noise

Communication not received from Inverter PCB for 10 seconds or more

Indoor Unit : Operation LED 9 times Flash, Timer LED 15 Times Flash,

Filter LED Continuous Flash.

Outdoor Unit : E. 6 2. 6

Error Code : 9 U / 6 2

Trouble shooting 29 E62. 6

Indicate or Display:

Detective Actuators:

Detective details:

OUTDOOR UNIT Error Method:

Forecast of Cause :

Caution

By changing of DIP SW 4-2 to ON, the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

(Stand alone outdoor unit is impossible)

The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

- The operating compressor life time becomes shorter.

- The operating performance may drop due to the limited active compressor(s).

- The compressor may stop frequently by protection controlling.

*In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

04-40

Содержание AB* A12GATH


















































































































































































































































Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды

Fujitsu AB* A12GATH, Руководство по обслуживанию

Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды