Fujitsu AB* A12GATH Скачать руководство пользователя страница 53

Страница: 53 / 241

3-1 FAN CONTROL

03-01

3-1-1 Fan Speed Setting

3. INDOOR UNIT OPERATION

AUTO

HIGH

MED

LOW

Press the FAN CONTROL button to set the fan speed.

Fan speed setting

3-1-2 "AUTO" Position

Fan speed zone

Hi zone

Med zone

Low zone

When the room

temperature decreases

When the room

temperature increases

3. DRY OPERATION

1. COOLING OPERATION

2. HEAT OPERATION

• Expansion

•

valve

• Indoor fan

motor

OFF

OPEN

CLOSE ON

30s

3min

2min30s

The indoor fan always rotates at "Lo" speed.

TIME -->

-T

(1) When the T

is changed.

(2) When the operation mode is changed from other mode to "COOL".

(3) When the fan control is changed from other position to "AUTO".

The fan speed is determined automatically in accordance

with the condition "(T

(corrected room temperature) - T

(corrected set temperature)" as shown on the right.

However, the fan speed zone is determined in the manner

as the room temperature increases for the following cases.

Same as Cooling operation, fan speed is decided by the

difference between the room temperature and the set

temperature.

(1) The indoor fan starts operation 5 seconds after the electric expansion valve opens. However, when the indoor unit just

starts its operation or the operation mode is changed from other to "DRY" and the refrigerant circulation is not stopped,

the fan will rotate immediately without a delay time of 5 seconds.

(2) The indoor fan will stop in 30 seconds when the refrigerant circulation stops.

(3) The indoor fan will stop immediately when the indoor unit is stopped by pushing the stop button or by a setting of ON timer.

(4) When the refrigerant circulation is stopped due to a lower room temperature for more then 3 minutes, the fan will rotate

2 minutes at intervals of 3 minutes.

(5) When the indoor unit just starts its operation or the operation mode is changed from other to "DRY" and the refrigerant

circulation is stopped, the fan will rotate for 1 minute and then it will operate according to the statement (4).

2min

Fan speed zone

Low zone

Med zone

Hi zone

When the room

temperature decreases

When the room

temperature increases

-2

-T

-2

-3

-T

-3

-T

-2

-T

-1

-2

-T

-1

-T

Содержание AB* A12GATH


















































































































































































































































Результаты поиска

Содержание AB* A12GATH

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu AB* A12GATH, Руководство по обслуживанию

Результаты поиска

Содержание AB* A12GATH

Отзывы:

Бренды по названию

Популярные бренды