manualshive.com logo in svg

Fujitsu AB* A12GATH, Руководство по обслуживанию

Поделиться
Скачать
Fujitsu AB* A12GATH Скачать руководство пользователя страница 41

< Operating state of each part during defrosting operation >

[ STEP 1 ]

02-13

[ STEP 2 ]

[ STEP 3 ]

Compressor

Heat Ex(4WV)

FAN

EEV1 

EEV2

EEV3

SV1,SV2

All compressor operaiotn Stop

Change Condensor (OFF)

Stops

0 pls

0 pls

Open (Balancing) 

All compressor start 

Condensor  (OFF)

Stops

EEV1: 300 pls

EEV2: 480 pls

100 - 500 pls

Close

All compressor operaiotn Stop

Keeps the operation mode 

Stops

0 pls

0 pls

Open

Preparation process

On Defrost operatiom 

Finishing process

Actuator

Slave 1

Slave 2

Compressor in operation

Compressor in operation

Stopped compressor

Master

Slave 1

Slave 2

Master

Slave 1

Slave 2

Master

INV

INV

INV

INV

INV

INV

INV

INV

INV

Compressor operate by 

the lowest speed (20rps)  

Outdoor units which satisfied the defrosting end judgment temperature

are operated at the lowest speed (20rps) for inverter compressor.

When the defrosting of all outdoor units ends, all outdoor unit stop. 

The start rotation execution is done, and restarts.

Defrosting

Defrosting

Defrosting

Defrost end

Defrost end

Defrost end

Defrost end

Defrost end

Defrosting

All compressors operates and it defrosting.

Содержание AB* A12GATH


















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды