Fujitsu AB* A12GATH Скачать руководство пользователя страница 239

Страница: 239 / 241

06-13

Remove the Compressor cover (Top).

Remove the Terminal Cover.

Remove the Discharge temp. thermistor

and Compressor shell temp. thermistor.

Remove the 3 mounting screws of Terminal.

Remove the Crank Case Heaters.

Comp.cover

(Top)

Color: White&

Green

Discharge temp. thermistor

(TH1)

Crank Case Heater

(2 places)

Hook (2 places)

Compressor shell temp. thermistor

(TH11)

Comp. cover

(Outside)

Color: Green

Comp. cover

(Accumulator)

Color: white

Note :

Compressor cover (Top) consists of 2 parts.

The inside of the Comp.cover is white, and

the outside of Comp.cover is green.

Remove the Compressor cover (Outside),

Compressor cover (Accumulator), and

Compressor cover (Body).

Comp. cover

(Body)

Color: White

Note the tightening torque at the installation.

Tightening torque is 2.0 ~2.5N m.

Note the tightening torque at the installation.

Crank Case Heater should not overlap each other.

Remove the Comp Bolts.

(4 places)

[U: Red, V: White, W: Black]

V(White)
U(Red)

W(Black)

Содержание AB* A12GATH


















































































































































































































































Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды

Fujitsu AB* A12GATH, Руководство по обслуживанию

Результаты поиска

Содержание AB* A12GATH

Отзывы:

Похожие инструкции для AB* A12GATH

Бренды по названию

Популярные бренды