Frontier RUT-G 2005 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 66

Frontier RUT-G 2005 Скачать руководство пользователя страница 49

Kele • RUT-G Manual 2005 • www.kele.com • USA 888-397-5353 • International 901-382-6084

51

RS232/485 INTERFACE KEY

RUT-G/RS232/485 INTERFACE KEY USER GUIDE

Figure 4

RF

Transceiver

Frontier Gateway Physical Layout

Serial Key,
Interface Module
Only one Interface
Module per
Gateway.
Refer to Figure 5
for jumper
settings.

Sockets for
additional Keys are
not supported and
additional Keys
should not be
installed

Power ON/OFF Switch

DIP Switches for Reset
of HTML defaults

Local

Processor

Frontier Radio Receive
and Transmit LEDs

Service (Reset)
Pushbuttons

Serial Key
Connections
(Pluggable)

Receive, Transmit, Status,
and Service (Reset) LEDs

Power Connection
(pluggable)

Frontier Gateway shown with one control module and two open sockets

Serial Key Interface Module

is the Interface between the user’s device and the Gateway. Refer to Table 7 for

key types.

Local Processor

is the main Frontier Gateway control unit. This processor handles all data to and from the RF

transceiver radio. The local processor communicates directly with the LonWorks control module.

RF Radio Transceiver

is the RF radio that transmits and receives data to/from the Frontier ﬁeld devices.

Receive, Transmit,

and

Status LEDs

indicate the Gateway’s activity on the user’s network.

«
...
47
48
49
50
51
...
»

Содержание RUT-G 2005



































































Отзывы:

Нет отзывов