manualshive.com logo in svg

frako 38-00400, Руководство по эксплуатации

Поделиться
Скачать
frako 38-00400 Скачать руководство пользователя страница 67

67

 10.1  Cleaning

DANGER! 
The following instructions must be observed to avoid danger to life and limb: 
- During cleaning, the instrument and the connecting cables must be isolated  
  from the power supply.  
- The isolated electrical system must be locked out to prevent its being  
  inadvertently switched on again. 
- The immediate vicinity must be covered. 
- All connections must be checked to verify that they are no longer live! 
- Power must not be switched on again to the installation until the cleaning 
  work is completed.
When work is carried out in the vicinity of the instrument terminals and con-
necting cables, there is a risk of live components being touched inadvertently. 
A moist cleaning cloth, which conducts electricity, must never be used. The 
working voltage may present a hazard to health or may even be life-threatening.
If the above instructions are followed, the risk of endangering life and limb can 
be significantly reduced.

The instrument may only be cleaned with a dry cloth. When this is done, the above safety  
instructions must be followed. All power to the instrument must be switched off before cleaning 
is begun. Power must not be switched on to the instrument again until the cleaning procedure is 
completed.
If the cleaning is restricted only to the front of the closed control cabinet, it is not necessary to 
isolate the PQC from the power supply, but in this case also only a dry cleaning cloth may be 
used.

 11 Decommissioning and removal, storage  
 

 and disposal

 11.1  Decommissioning and removal

When decommissioning and removal work is carried out, please note the following:

DANGER! 
The following instructions must be observed to prevent danger to life and limb 
or damage to equipment and other assets: 
- When the instrument is removed, it is essential to switch off the power to the  
  instrument and the installation beforehand. 
- The isolated electrical system must be locked out to prevent its being  
  inadvertently switched on again. 
- All connections must be checked to verify that they are no longer live! 
- All live components in the immediate vicinity must be covered to prevent 
  inadvertent contact.
When work is carried out on the instrument terminals and connecting cables, 
there is a risk of live components being touched inadvertently. The working 
voltage may present a hazard to health or may even be life-threatening.

Содержание 38-00400









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды