FlightSafety LEARJET 45 Скачать руководство пользователя страница 466

Страница: 466 / 539

Manual AP Control

The airplane can be controlled manually when

the autopilot is engaged. The bottom portion

(barrel) of the control wheel trim switch

(CWTS) can be used as a manual controller if

the arming button, on top of the switch, is not

depressed (Figure 16-47). Manual control is

only possible from the CWTS on the coupled

side.

Moving the barrel forward or aft, without de-

pressing the arming button, commands cor-

r e s p o n d i n g p i t c h c h a n g e s t h r o u g h t h e

autopilot. Left or right movement (arming

button not depressed) commands roll changes.

Once the AP is engaged, depressing the arm-

ing button and moving the barrel in any di-

rection disengages the autopilot (but not the

YD).

When manual control is used to command roll,

any FD lateral modes previously captured (ex-

cept APP and LOC) will be cleared and the AP

will maintain the new roll attitude, existing

when the barrel is released. Similarly, when

a pitch change is commanded, any FD pitch

modes that were captured (except glideslope)

will be cleared and the AP will maintain the

new pitch attitude, existing when the barrel is

released.

Once glideslope, approach or localizer has

been captured, manual control barrel pitch

and roll commands will not be followed.

Touch Control Steering (TCS)

The touch control steering (TCS) switch is

used to temporarily take control from the au-

topilot when it is engaged. It can also be used

as a FD pitch or roll sync switch when the AP

is disengaged.

With autopilot engaged, depressing and hold-

ing either TCS button disengages the clutch on

the pitch and roll servos. This does not dis-

engage the AP, but allows the airplane to be

maneuvered as desired. The crew should not

apply control wheel pressure when the AP is

engaged unless the TCS button is first de-

pressed and held. Applying aileron or eleva-

tor control wheel pressure without depressing

the TCS may result in an AP monitor discon-

nect.

While the TCS button is held depressed (AP

engaged), a white “TCS” annunciator appears

at the top of the PFDs. In addition, selected

FD modes remain engaged and the command

bars sync to the existing airplane attitude.

Once released, the pitch and roll clutch ser-

vos re-engage and give airplane control back

to the autopilot. Previously engaged vertical

modes (SPD, VS or ALT) will synchronize to

the new existing flight conditions and lateral

modes will attempt to recapture. If flight level

change (FLC) was engaged, the FD will re-in-

tercept the previously selected profile.

If FD lateral modes were not engaged (ROL

hold), and the TCS button is released at bank

angles greater than 30°, the autopilot will roll

the airplane to 30° and maintain that bank

angle. If the bank angle is within 6° of level

flight, when the TCS button is released, the AP

will roll the airplane to a wings level attitude.

When the AP is not engaged, the TCS button

also acts as a pitch or roll sync switch. If the

airplane is in a pitch hold mode (PIT), de-

pressing the button synchronizes the com-

mand bars to the existing pitch attitude. If

SPD, VS or ALT vertical modes are engaged,

they will sync to the existing values when the

TCS button is depressed and released. The

SPD bug will also synch to the current airspeed

when the TCS button is momentarily depressed

while in the basic pitch mode (with a lateral

mode).

L E A R J E T 4 5

P I L O T T R A I N I N G M A N U A L

16-82

FOR TRAINING PURPOSES ONLY

FlightSafety

international

Содержание LEARJET 45




























































































































































































































































































































































































































































































































































Результаты поиска

Содержание LEARJET 45

Отзывы:

FlightSafety LEARJET 45, Руководство по подготовке пилотов, Страница: 466 / 539

Результаты поиска

Содержание LEARJET 45

Отзывы: