FLENDER K.A Series Скачать руководство пользователя

Страница: 40 / 128

Further information

Further information and a detailed illustration of the gear unit and the position of the mounted

components can be found in the dimension drawing in the complete documentation for the gear

unit.
Further information about bearing monitoring using a Pt 100 resistance thermometer (such as

control instructions) and the technical data can be found in the operating instructions for the Pt

100 resistance thermometer and in the list of equipment in the complete documentation for the

gear unit.

3.15.2

Bearing monitoring by acceleration sensor

Depending on the order specification, the gear unit can be supplied with threaded holes in

which acceleration sensors can be inserted. These threaded holes have an M6 or M8 thread

depending on the variant.

①

Shock-pulse transducer

Figure 3-12

Bearing monitoring using a shock-pulse transducer

The following diagram shows the complete acceleration sensor (A) and the threaded connector

(B):

Description
3.15 Bearing monitoring

REDUREX Gear unit 5200en

Operating Instructions 03/2019

Содержание K.A Series

































































































































Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды

FLENDER K.A Series, Руководство по эксплуатации

Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды