manualshive.com logo in svg

FLENDER K.A Series, Руководство по эксплуатации

Поделиться
Скачать
FLENDER K.A Series Скачать руководство пользователя страница 13

Safety instructions

2

2.1

Security notes

Flender offers products and solutions with industrial security functions, which support the safe 

and secure operation of plants, systems, machines and networks.
In order to safeguard plants, systems, machines and networks against cyber threats it is 

necessary to implement (and continually maintain) a holistic industrial security concept that 

corresponds to the current state of the art. Flender products and solutions undergo continuous 

development in this respect.
Customers are responsible for preventing unauthorised access to their plants, systems, 

machines and networks. Systems, machines and components shall only be connected to the 

company network or the Internet when and as far as this is absolutely necessary and 

appropriate protective measures (e.g. use of firewalls and network segmentation) shall be 

taken. 
In addition the recommendations of Siemens regarding appropriate protective measures shall 

be observed. You can find further information about Industrial Security at:

https://www.siemens.com/industrialsecurity
Flender products and solutions undergo continuous development in order to make them even 

safer. Flender strongly recommends that you regularly carry out any updates as soon as they 

are available and that you only use the current product versions. Use of older or no longer 

supported versions can increase the risk of cyber threats. 
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS 

Feed at:

https://www.siemens.com/industrialsecurity

2.2

The five safety rules

In order to protect yourself and prevent any damage to property, always observe the safety 

relevant information and the following five safety rules (as per EN 50110-1 "Working on isolated 

equipment") when working on electrical components of the plant.
Prior to starting work on the machine, follow the safety rules listed below:
1. Disconnect

Also disconnect auxiliary circuits such as the anti-condensation heater

2. Safeguard against restart
3. Ensure that the system is de-energised
4. Earth and short circuit
5. Cover or cordon off adjacent live parts
When all the work is complete, cancel the safety measures in the reverse sequence.

REDUREX Gear unit  5200en

Operating Instructions 03/2019

13

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды