FLENDER K.A Series Скачать руководство пользователя | Manualshive

Страница: 17 / 128

background image

Switch the gear unit to standstill immediately if inexplicable changes are noticed during

operation. Such changes may include unusual gear unit noise or a significant increase in

operating temperature.

WARNING

Risk of falling
There is an increased risk of falling when standing or walking on the gear unit during operation.
Only walk or stand on the gear unit and its mounted components for maintenance and repair

work when it is at a standstill. Do not walk or stand on shaft ends, protection covers, mounted

components or pipes.

WARNING

Danger to life through rotating or moving parts
There is danger that rotating or moving parts may catch hold of you or pull you in.
Secure rotating and/or moving parts against contact using safeguards.

Surface temperature

The surface temperatures of the gear unit can become very extreme depending on the

operating conditions.

WARNING

Risk of burns
Possible risk of serious burn injury from hot surfaces (> 55 °C).
Wear suitable protective gloves and protective clothing.

WARNING

Risk of scalding
Risk of serious injury possible through escaping hot operating media when these are being

changed.
Wear suitable protective gloves, safety goggles and protective clothing.

WARNING

Danger due to low temperatures
Possible risk of serious injuries due to frost (pain, numbness, frostbite) on cold surfaces

(< 0 °C).
Wear suitable protective gloves and protective clothing.

Safety instructions

2.5 Special types of danger and personal protective equipment

REDUREX Gear unit 5200en

Operating Instructions 03/2019

17

«
...
15
16
17
18
19
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: HAMAR LASER Страницы: 49

Бренд: Haki Страницы: 24

Бренд: Dakota Digital Страницы: 5

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: Obdstar Страницы: 42

Бренд: Haaga Страницы: 31

Бренд: Jacobsen Страницы: 20

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: ALL-FILL Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды