FLENDER K.A Series страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 128

background image

Chemical substances

Injuries can be sustained when using chemical substances.

WARNING

Risk of chemical burns due to chemical substances
There is a risk of chemical burns when handling aggressive cleaning agents.
Please observe the manufacturer's guidelines on how to handle cleaning agents and solvents.

Wear suitable protective equipment (gloves, safety goggles). Please use binding agents to

immediately clear up any spilt solvent.

CAUTION

Risk of injury due to chemically aggressive operating materials
There is a risk of injury to eyes and hands when handling chemically aggressive operating

materials.
Please observe the safety instructions in the data sheets of the oil used. Wear suitable

protective equipment (gloves, safety goggles). Use an oil-binding agent to immediately clean

up spilt oil.

Danger of explosion

An explosion may occur in a potentially explosive atmosphere.

DANGER

Danger of explosion through ignition of a potentially explosive atmosphere
Danger to life through ignition of a potentially explosive atmosphere possible when operating

the gear unit
Do not use the gear unit in potentially explosive atmospheres.

2.6

Intended use

Only use the gear unit according to the conditions specified in the service and delivery contract

and the technical data in the annex (Page 113). Deviating operating conditions are considered

improper use. The user or owner of the machine or plant is solely liable for any resulting

damage.

Safety instructions
2.6 Intended use

REDUREX Gear unit 5200en

18

Operating Instructions 03/2019

«
...
16
17
18
19
20
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: B-K lighting Страницы: 3

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGER WERKEN Страницы: 2

Бренд: Abus Страницы: 8

EPL-HB-150LED-RT-IBSC

Бренд: Larson Electronics Страницы: 2

Бренд: Heidolph Страницы: 36

Бренд: GCE druva Страницы: 152

Бренд: iFIT Страницы: 4

Бренд: Fast Mover Страницы: 2

Бренд: Chord Страницы: 10

Бренд: Paloma Страницы: 12

Aesculap activ C

Бренд: Braun Страницы: 41

N3242-1 Heron Lift E

Бренд: Wealden Rehab Страницы: 11

Бренд: Lanta Страницы: 8

Бренд: Roland Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды