FLENDER K.A Series страница 76 Скачать руководство пользователя | Manualshive

Страница: 76 / 128

background image

Further information

You can find additional information about the electrical connections in the terminal diagrams

and equipment lists provided in the complete gear unit documentation.

5.7.7

Connecting the oil temperature monitor

Procedure

To connect the Pt 100 resistance thermometer, proceed as follows:
1. Check that the Pt 100 resistance thermometer connection is not damaged.
2. Install the electrical wiring between the Pt 100 resistance thermometer and the evaluation

unit. The customer is responsible for providing the evaluation unit.

Further information

Further information about the Pt 100 resistance thermometer can be found in the Pt 100

resistance thermometer operating instructions in the complete documentation for the gear unit.

5.7.8

Connecting the oil-level monitoring system

Procedure

To connect the oil-level monitoring system to the gear unit, proceed as follows:
1. Ensure that the filling level limit switch connection is not damaged.
2. Electrically connect the filling level limit switch.
3. Connect the signal so that for the "oil level too low" signal, the drive motor cannot start and

an alarm is output.

Bypass this signal in operation.

Further information

Additional information about the oil-level monitoring system can be found in the operating

instructions for the oil-level monitoring system components provided in the complete gear unit

documentation.
You can find technical data in the separate data sheet and in the equipment list in the complete

gear unit documentation.

Mounting
5.7 Connecting components

REDUREX Gear unit 5200en

76

Operating Instructions 03/2019

«
...
74
75
76
77
78
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: B&G Страницы: 3

Бренд: Rangevision Страницы: 28

Бренд: Patty-O-Matic Страницы: 28

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: Vahterus Страницы: 31

Бренд: Yamaha Страницы: 48

Бренд: Yamaha Страницы: 85

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 200

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды