FLENDER K.A Series Скачать руководство пользователя | Manualshive

Страница: 69 / 128

background image

5.5.1.1

Pulling on with integrated DU bushing

Procedure

NOTICE
Damage to the gear unit
The gear unit can become damaged if it skews during assembly.
The hollow shaft must be flush with the machine shaft during assembly of the gear unit on the

machine shaft. The gear unit must be prevented from skewing.

NOTICE
Damage to the rolling-contact bearings
The rolling-contact bearings can become damaged if the gear unit skews during mounting.
The hollow shaft may be mounted on a machine shaft shoulder only if the gear unit features

one of the following:
● Torque arm
● Supported by gear unit swing base

Proceed as follows to mount the gear unit with hollow shaft and shrink disk onto the driven

machine shaft with integrated DU bushing:
1. Use suitable hoisting gear to lift the gear unit.
2. Mount the gear unit using the nut and screw spindle.

The gear unit is supported by the hollow shaft.

3. Quickly pull the shaft into the hollow shaft up to the end plate.

Mounting

5.5 Shaft-mounted gear unit with hollow shaft and shrink disk

REDUREX Gear unit 5200en

Operating Instructions 03/2019

69

«
...
67
68
69
70
71
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Ecco Страницы: 3

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: AAON Страницы: 36

Бренд: ACDC Страницы: 4

Бренд: Eaton Страницы: 16

RMQ-Titan C22-PV Series

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 98

Бренд: Eaton Страницы: 15

Бренд: Sagola Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды